|
|
|
|
|
|
|
|
|
|
|
Water heater supply line washer.
|
Permanent installation, fits directly into water heater for easy draining. 2-1/2" length.
|
Anti-siphon hole breaks damaging siphon action. Can be cut to desired length. Made of PEX. With gasket.
|
|
|
|
|
|
|
|
|
|
|
|
|
Everything needed to install flat, screw-in and universal flange elements. Contains: (1) screw-in gasket, (1) universal flange gasket, (1) four hole gasket and (4) 1/4" - 20 x 3/4" hex bolts.
|
Rated for 250 PSI at 180DegF. Threaded ends comply with ANSI B1.20.1. Solder ends comply to ANSI 16.18.
|
For water heater inlet and outlet hook-ups and other uses where dissimilar metals occur in piping and plumbing systems. Thermoplastic lining prevents corrosion. 2-1/2" length.
|
|
|
|
|
|
|
|
|
|
|
|
|
Rated for 250 PSI at 180DegF. Threaded ends comply with ANSI B1.20.1. Solder ends comply to ANSI 16.18.
|
UL Listed, gasket included.
|
Rated for 250 PSI at 180DegF. Threaded ends comply with ANSI B1.20.1. Solder ends comply to ANSI 16.18.
|
|
|
|
|
|
|
|
|
|
|
|
|
Contains: (1) 2-1/2" 4-bolt, (1) screw-in gasket adapt-a-flange, (1) thermostat bracket, (1) four hole gasket and (4) 5/16" - [no. 18] 5/8" hex bolt-washers. Use a standard screw-in element to replace a flat, universal or round flange element using the element conversion kit.
|
1-1/4" shank length. Heavy brass construction. Neoprene seal disc. 3/4" hose threaded outlet. Plated steel canopy handle. Pipe threads comply with ANSI B1.20.01. Hose threads comply with ANSI B1.20.7.
|
Connector with nickel plated brass nuts and nitrile rubber sealing washer. Complies with no-lead laws. 3/4" FIP x 3/4" FIP.
|
|
|
|
|
|
|
|
|
|
|
|
|
Internal dielectric sleeve effectively separates dissimilar metals within the waterway to prevent galvanic and electrolytic corrosion. Nitrile rubber washer is more resilient than PEX and easier to install on rough nipple surfaces. A greater number of thread to thread contact provides a better seal to lined nipples. Specially engineered brass adapter allows direct connection to PEX pipe. Design-certified and manufactured in accordance with ANSI/ASME A112.18.6, ANSI /NSF-61 (Section 9), CSA B125, UL Laboratories MH25826 report, and NES NER-615 report.
|
Rated for 250 PSI at 180DegF. Threaded ends comply with ANSI B1.20.1. Solder ends comply to ANSI 16.18.
|
Turn off electric change you element without draining your water heater, by turning off water at the water heater to create a vacuum. Remove wires from element put quick change tool on neoprene nub behind element add bucket or basin, have new element handy take out and replace you should not lose more then 2" of water.
|
|
|
|
|
|
|
|
|
|
|
|
|
UL Listed, gasket included.
|
For electric water heaters only. Heavy duty polypropylene. Dual size 1 inch to 1.5 inch PVC drain fitting with gaskets included. Sides are 2.5 inches deep. Pre-cut side opening for drain fitting.
|
UL listed. Meets original specification length for State, Reliance, Kenmore, Bradford White. Energy efficient range setting, built-in safety switch to prevent overheating.
|
|
|
|
|
|
|
|
|
|
|
|
|
UL Listed. Meets original specifications length for Rheem, Ruud, Richmond, A.O.Smith, American and GSW. Energy efficient range setting, built-in safety switch to prevent overheating.
|
Connector with nickel plated brass nuts and nitrile rubber sealing washer. Complies with no-lead laws. 3/4" FIP x 3/4" FIP.
|
Test your elements and thermostats while still in the water heater. 1 piece.
|
|
|
|
|
|
|
|
|
|
|
|
|
UL Listed, gasket included.
|
3/4" temperature and pressure relief valve with 4" probe. All brass body, stainless steel spring, factory set at 150 PS, crafted with no gaskets and epoxy-coated probes to prevent corrosion buildup. ANS Z21.22 design, AGA certified, furnished with test lever.
|
UL Listed, gasket included.
|
|
|
|
|
|
|
|
|
|
|
|
|
UL Listed, gasket included.
|
UL Listed, gasket included.
|
For electric water heaters only. Heavy duty polypropylene. Dual size 1 inch to 1.5 inch PVC drain fitting with gaskets included. Sides are 2.5 inches deep. Pre-cut side opening for drain fitting.
|
|
|
|
|
|
|
|
|
|
|
|
|
Internal dielectric sleeve effectively separates dissimilar metals within the waterway to prevent galvanic and electrolytic corrosion. Nitrile rubber washer is more resilient than PEX and easier to install on rough nipple surfaces. A greater number of thread to thread contact provides a better seal to lined nipples. Specially engineered brass adapter allows direct connection to PEX pipe. Design-certified and manufactured in accordance with ANSI/ASME A112.18.6, ANSI /NSF-61 (Section 9), CSA B125, UL Laboratories MH25826 report, and NES NER-615 report.
|
For electric water heaters only. Heavy duty polypropylene. Dual size 1 inch to 1.5 inch PVC drain fitting with gaskets included. Sides are 2.5 inches deep. Pre-cut side opening for drain fitting.
|
Seamless corrugated 18" flexible copper water connectors. 125 PSI maximum.
|
|